03 CHEVY VENTURE HOW TO
03 CHEVY VENTURE INSTALL
03 CHEVY VENTURE SERIES
03 CHEVY VENTURE FREE

The variety of Chevrolet Venture for saleĬhevrolet Venture for sale was first launched in the Philippines market since 2003. Although new models are frequently more modern and feature-rich, are all new models better than the previous generation? Is buying second-hand cars for sale a bad decision? The answer will be revealed in this article. We're the company that's here for you on the Internet and in person.Should You Buy Chevrolet Venture 2003 for sale?Īfter a period of promoting older models, Chevrolet Venture Philippines frequently updates Chevrolet car for sale to entice customers to spend money on premium models.

03 CHEVY VENTURE FREE

Please feel free to call us, toll-free, 88. Brought to you by you're source for quality replacement parts and the best service on the Internet.

Mirror, lock, window, and you're all set. You don't want it to be too tight because they just go into plastic so it could strip out. This screw I put into my extension socket first. Then there's a pin in the front that just guides it. I can look back here because it's easy to see this pin and guide it right in there. Make sure you get all your harnesses up and through. There's clips that the window has to go into it goes in between. Take your pliers, put them on nice and tight. What we can do is you'll put this spring back on, and you want it down like that. We can take our pliers and crimp - I forgot to do this before, should have really done this before. What's easiest is to turn the key on, take your car window switch and run your regulator all the way up. It's OK that it's in a different spot than where it was originally. You have to have it kind of forward and slide it back to where the motor is. The track kind of came apart a little bit no big deal. You'll feel the end of this track here get that in. Then that one slides in, so we're all set there again. Slide that one in, then this little spacer goes in. Then what we'll do is I put a little bit of grease on my slider there. Your regulator from 1A Auto, and just for comparison, you can see, it's just like the old one. So you release the crimp on that track just keep in mind which way this is going. Now what you want to do is take either your big pliers or needle-nose pliers, and the regulator has been crimped on the ends here, so you have to bend that back out. You just need to slide it back, and out of that track, and not get your hands pinched in there, and the regulator comes right out. Turn this counterclockwise with the screwdriver while you hold onto the regulator, and then pull it out. This spring has a lot of tension on it, so when you get it off you want to be ready because it's going to want to turn your wrists. With a nice big pair of pliers, to remove your window regulator, you're going to release this balance spring. Now you can see I lifted the window up, and used some painter's tape just to secure it. You press those tabs you press the tabs and at the same time - you see this is sliding - slide your window track back, and that unlocks the window. Sounds a little weird but basically there's a couple tabs. You want to unlock your window from your window track. Next you're going to want to remove your water shield carefully. Work my way right around the door panel, and then it comes off. I actually just worked my fingers right underneath up here. So you can use a putty knife or something to get underneath.

03 CHEVY VENTURE SERIES

Those out, now there's just a series of pins around the outside perimeter and then 2 right in here that need pulled out. I'm using a 10mm socket with a ratchet and extension. One right in there, and one right down there.

Now, again with the screwdriver, I'm going to pry out this bezel here, got your door handle. I've already done that before, so it looked kind of easy that will require some force usually, the first time. Then this mirror switch there's a little tab right here that you need to pry back with your fingernail or a screwdriver, then pull the connector out. I find it easiest just to press on this black tab and then pry. First, you're going to want to pry up this switch plate. Tools you'll need are a 10mm socket and ratchet, a flat-blade screwdriver, and a pair of large pliers.

03 CHEVY VENTURE HOW TO

In this video, we're going to show you how to replace the driver's side window regulator, which is the same as the passenger side regulator on this '98 Venture, and that's basically the same as any '97-'05 Venture, Montana, Transport or Silhouette.

03 CHEVY VENTURE INSTALL

I'm going to use my 20+ years' experience restoring and repairing cars and trucks like this to show you the correct way to install parts from. I want to help you save time and money repairing and maintaining your vehicle. Brought to you by, your source for quality replacement parts and the best service on the Internet.

03 chevy venture